No - this not makes it to boot and yet I don’t know if this has any good or bad effect at all other than no warning. This have to be something else. I’m quite sure that I tested those two images and they worked perfectly and now I cant recreate them on second card, give me some time and hopefully I’ll find issue. Still it’s much easier if I see same problem.
BTW: here is Your requested log
DDR Version V1.10 20210810
In
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB
tdqss: cs0 dqs0: 48ps, dqs1: -48ps, dqs2: -48ps, dqs3: -144ps,
tdqss: cs1 dqs0: 72ps, dqs1: -72ps, dqs2: -24ps, dqs3: -144ps,
change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x61
change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x36
cs 0:
the read training result:
DQS0:0x39, DQS1:0x3b, DQS2:0x41, DQS3:0x34,
min : 0x8 0xa 0xa 0xa 0x1 0x3 0x6 0x2 , 0x8 0x6 0x1 0x3 0xb 0x9 0xb 0x8 ,
0x13 0x12 0xe 0xd 0x7 0x2 0x4 0x7 , 0x7 0x5 0x5 0x1 0x9 0x9 0x6 0x9 ,
mid :0x24 0x27 0x28 0x26 0x1c 0x1f 0x21 0x1f ,0x25 0x24 0x1f 0x20 0x29 0x26 0x27 0x25 ,
0x30 0x30 0x2b 0x2a 0x25 0x21 0x23 0x24 ,0x23 0x21 0x20 0x1c 0x25 0x24 0x22 0x25 ,
max :0x41 0x44 0x46 0x43 0x37 0x3b 0x3d 0x3d ,0x43 0x43 0x3d 0x3e 0x47 0x44 0x44 0x43 ,
0x4e 0x4f 0x48 0x48 0x43 0x40 0x43 0x42 ,0x3f 0x3d 0x3c 0x37 0x41 0x40 0x3f 0x42 ,
range:0x39 0x3a 0x3c 0x39 0x36 0x38 0x37 0x3b ,0x3b 0x3d 0x3c 0x3b 0x3c 0x3b 0x39 0x3b ,
0x3b 0x3d 0x3a 0x3b 0x3c 0x3e 0x3f 0x3b ,0x38 0x38 0x37 0x36 0x38 0x37 0x39 0x39 ,
the write training result:
DQS0:0x3c, DQS1:0x30, DQS2:0x30, DQS3:0x23,
min :0x61 0x63 0x64 0x63 0x5a 0x5d 0x5f 0x60 0x5f ,0x5b 0x5b 0x55 0x58 0x60 0x5d 0x5f 0x5e 0x5a ,
0x58 0x5a 0x53 0x55 0x4f 0x4d 0x50 0x50 0x52 ,0x51 0x50 0x4e 0x4d 0x54 0x54 0x52 0x57 0x4e ,
mid :0x7d 0x7f 0x80 0x7f 0x74 0x78 0x7a 0x7a 0x79 ,0x75 0x73 0x6d 0x6f 0x78 0x74 0x76 0x77 0x71 ,
0x74 0x74 0x6e 0x6f 0x67 0x64 0x65 0x69 0x6c ,0x6c 0x69 0x67 0x65 0x6d 0x6e 0x6a 0x6f 0x64 ,
max :0x99 0x9b 0x9c 0x9b 0x8f 0x93 0x96 0x95 0x93 ,0x90 0x8c 0x86 0x87 0x91 0x8c 0x8e 0x90 0x89 ,
0x90 0x8f 0x8a 0x89 0x80 0x7b 0x7b 0x82 0x86 ,0x88 0x82 0x81 0x7d 0x86 0x88 0x83 0x88 0x7b ,
range:0x38 0x38 0x38 0x38 0x35 0x36 0x37 0x35 0x34 ,0x35 0x31 0x31 0x2f 0x31 0x2f 0x2f 0x32 0x2f ,
0x38 0x35 0x37 0x34 0x31 0x2e 0x2b 0x32 0x34 ,0x37 0x32 0x33 0x30 0x32 0x34 0x31 0x31 0x2d ,
cs 1:
the read training result:
DQS0:0x3a, DQS1:0x39, DQS2:0x3f, DQS3:0x37,
min : 0x9 0xa 0xb 0xa 0x1 0x6 0x6 0x2 , 0x7 0x5 0x1 0x2 0xa 0x8 0xa 0x7 ,
0xe 0xe 0xa 0xa 0x3 0x2 0x1 0x5 , 0x9 0x6 0x6 0x2 0xb 0xb 0x8 0xa ,
mid :0x25 0x27 0x28 0x26 0x1b 0x20 0x20 0x1f ,0x23 0x23 0x1e 0x1e 0x28 0x25 0x26 0x24 ,
0x2b 0x2c 0x27 0x27 0x21 0x20 0x20 0x22 ,0x25 0x23 0x22 0x1e 0x28 0x27 0x26 0x27 ,
max :0x41 0x44 0x46 0x43 0x36 0x3b 0x3b 0x3c ,0x40 0x41 0x3b 0x3b 0x46 0x42 0x43 0x41 ,
0x49 0x4a 0x45 0x45 0x3f 0x3e 0x3f 0x3f ,0x42 0x40 0x3f 0x3b 0x45 0x44 0x44 0x44 ,
range:0x38 0x3a 0x3b 0x39 0x35 0x35 0x35 0x3a ,0x39 0x3c 0x3a 0x39 0x3c 0x3a 0x39 0x3a ,
0x3b 0x3c 0x3b 0x3b 0x3c 0x3c 0x3e 0x3a ,0x39 0x3a 0x39 0x39 0x3a 0x39 0x3c 0x3a ,
the write training result:
DQS0:0x3c, DQS1:0x30, DQS2:0x30, DQS3:0x23,
min :0x67 0x68 0x69 0x68 0x5e 0x61 0x64 0x66 0x63 ,0x55 0x55 0x4f 0x52 0x5a 0x57 0x5a 0x59 0x54 ,
0x5e 0x5f 0x58 0x5a 0x54 0x50 0x53 0x57 0x58 ,0x4f 0x4f 0x4c 0x49 0x53 0x52 0x50 0x54 0x4c ,
mid :0x83 0x84 0x85 0x83 0x78 0x7c 0x7f 0x7f 0x7e ,0x71 0x6f 0x6a 0x6b 0x73 0x70 0x73 0x71 0x6e ,
0x79 0x79 0x72 0x73 0x6c 0x68 0x6b 0x6e 0x71 ,0x6a 0x67 0x64 0x62 0x6c 0x6b 0x66 0x6e 0x64 ,
max :0x9f 0xa1 0xa2 0x9f 0x93 0x98 0x9a 0x99 0x99 ,0x8d 0x89 0x85 0x85 0x8d 0x8a 0x8c 0x8a 0x88 ,
0x95 0x94 0x8d 0x8c 0x85 0x80 0x84 0x86 0x8b ,0x86 0x80 0x7c 0x7b 0x85 0x85 0x7d 0x89 0x7c ,
range:0x38 0x39 0x39 0x37 0x35 0x37 0x36 0x33 0x36 ,0x38 0x34 0x36 0x33 0x33 0x33 0x32 0x31 0x34 ,
0x37 0x35 0x35 0x32 0x31 0x30 0x31 0x2f 0x33 ,0x37 0x31 0x30 0x32 0x32 0x33 0x2d 0x35 0x30 ,
CA Training result:
cs:0 min :0x51 0x52 0x45 0x46 0x47 0x43 0x4d ,0x4d 0x4a 0x45 0x44 0x46 0x41 0x4a ,
cs:0 mid :0x90 0x8f 0x84 0x83 0x85 0x81 0x7d ,0x8b 0x88 0x85 0x82 0x84 0x80 0x7a ,
cs:0 max :0xcf 0xcd 0xc4 0xc1 0xc4 0xbf 0xad ,0xca 0xc7 0xc5 0xc0 0xc2 0xc0 0xab ,
cs:0 range:0x7e 0x7b 0x7f 0x7b 0x7d 0x7c 0x60 ,0x7d 0x7d 0x80 0x7c 0x7c 0x7f 0x61 ,
cs:1 min :0x4d 0x53 0x42 0x4a 0x42 0x45 0x4b ,0x49 0x4c 0x41 0x47 0x40 0x45 0x48 ,
cs:1 mid :0x8f 0x8e 0x84 0x84 0x84 0x80 0x7c ,0x8b 0x88 0x83 0x82 0x82 0x80 0x78 ,
cs:1 max :0xd1 0xca 0xc7 0xbf 0xc6 0xbb 0xad ,0xce 0xc4 0xc6 0xbe 0xc4 0xbc 0xa9 ,
cs:1 range:0x84 0x77 0x85 0x75 0x84 0x76 0x62 ,0x85 0x78 0x85 0x77 0x84 0x77 0x61 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Nov 19 2021 - 08:09:37)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256+ OK
## Checking uboot 0x00a00000 ... sha256+ OK
## Checking fdt 0x00b24098 ... sha256+ OK
## Checking atf-2 0x00068000 ... sha256+ OK
## Checking atf-3 0xfdcd0000 ... sha256+ OK
## Checking atf-4 0xfdcc9000 ... sha256+ OK
## Checking atf-5 0x00066000 ... sha256+ OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 232.871 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-167-g81e0b993a-dirty:xsf
NOTICE: BL31: Built : 11:20:08, Sep 6 2021
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09-armbian (Nov 19 2021 - 08:09:37 +0000)
Model: Radxa ROCK 3 Model A
PreSerial: 2, raw, 0xfe660000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: ed354000, fdt: eb9f8d78
Using default environment
no mmc device at slot 1
dwmmc@fe2b0000: 1 (SD), dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 50Mhz
PartType: DOS
No misc partition
boot mode: None
FIT: No boot partition
No resource partition
Failed to load DTB
Failed to get kernel dtb, ret=-19
io-domain: OK
Model: Radxa ROCK 3 Model A
rockchip_set_serialno: could not find efuse/otp device
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 24000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 100000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 50000 KHz
aclk_top_high 300000 KHz
aclk_top_low 200000 KHz
hclk_top 150000 KHz
pclk_top 50000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 50000 KHz
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 20 ms (155.3 KiB/s)
## Executing script at 00c00000
Boot script loaded from mmc 1
200 bytes read in 17 ms (10.7 KiB/s)
6125256 bytes read in 541 ms (10.8 MiB/s)
22170112 bytes read in 1878 ms (11.3 MiB/s)
146874 bytes read in 93 ms (1.5 MiB/s)
** File not found /boot/dtb/rockchip/overlay/rk35xx-fixup.scr **
Fdt Ramdisk skip relocation
## Loading init Ramdisk from Legacy Image at 0a200000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 6125192 Bytes = 5.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
reserving fdt memory region: addr=a100000 size=8a000
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a18cfff
Adding bank: 0x00200000 - 0xf0000000 (size: 0xefe00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 3101.860 ms
Starting kernel ...
Armbian 21.11.0-trunk Bullseye ttyFIQ0
rock-3a login:
This one is from system moved to nvme, but this makes difference after kernel load.